top of page
shutterstock_1669806082.jpg

Monitoring Prism Research Report

We recently conducted a study of the technical considerations involved with making a monitoring prism / survey prism selection for deformation monitoring in a mining environment to ensure the highest quality results.

We investigated the unique design aspects that influence performance of a monitoring prism / survey prism and which prism attributes best suit the conditions for mining/mining sector.

View the report below.

Prism Research Reprt

ABSTRACT

This study presents an overview of the technical considerations involved with making a monitoring prism / survey prism selection for deformation monitoring in a mining environment to ensure the highest quality results. We will investigate the unique design aspects which influence the performance of a monitoring prism / survey prism and which prism attributes best suit the mining conditions.

INTRODUCTION

Monitoring prisms are an important part of the measuring process. Typically, spatial professionals widely accept that they are an accurate, reliable accessory without much consideration of the influence monitoring prism / survey prism have on the quality of their measurements. Obtaining a high level of accuracy and reliability requires consideration of all possible effects on the measurements. A strong emphasis is placed on the specifications and accuracies of the total station, as it should be, but too often the considerations for prism selection are non-existent or fall back to a fiscal decision.

 

There are various applications where the required 3D accuracies are in the magnitude of centimetres but tasks such as deformation monitoring require much higher accuracies, in the order of millimetres. To achieve this level of accuracy and reliability we must look at the errors associated with monitoring prism / survey prism selection and the associated effects in the mining environment.

REFLECTOR TYPES

Most spatial professionals have encountered three typical types of reflectors. Round monitoring prism types in varied diameters, 360⁰ monitoring prisms and multiples of prism banks.

360⁰ monitoring prisms have been developed for use with robotic total stations for increased tracking abilities but do not work well with stationary targets as with deformation monitoring where the EDM is used in a single burst. Multiple banks of monitoring prisms / survy prisms will increase the amount of signal available for retro reflection of the EDM, useful if you are only acquiring a distance, but multiple monitoring prisms / survey prisms disrupt the ability to make repeatable angular measurements resulting in scattered 3D accuracies. The best reflector type for deformation monitoring is a single 64mm ɸ round prism, aligned perpendicular to the total station. In scenarios where the reflector and/or total station is adversely affected by ambient light or condensation early in the morning, considerations should be made to include a hood on the prisms to increase repeatability of the measurements.

REFLECTOR ACCURACIES

When a montioring prism / survey prism is manufactured, a piece of glass is ground to establish reflective angles. The quality of the grinding plays a key role when reflecting signals, the more accurate and angle is achieved the better the signal will be returned in the same direction. The intensity of the return signal is also stronger, a crucial point for the mining environment given the climatic conditions.

The deviation between incoming and outgoing beams, known as beam deviation or the stated accuracy, has a critical influence on the measurement range.

Reflector Accuracies - Prism Monitoring

Figure 1

Figure 1 depicts a monitoring prism with a small beam divergence, approximately 2 arc seconds or less. The outgoing signal is retro reflected to the emitter optics, total station, with a strong intensity. Note the signal affected by beam divergence out of the total station that misses the reflector as well as signal reflected from the extremities of the monitoring prism that is not returned to the receiver optics.

Reflector Accuracies - Prism Monitoring

Figure 2

Figure 2 depicts the effects of poor beam divergence from a prism with a greater accuracy of 2 arc seconds. The same amount of signal makes it to the monitoring prism / survey prism as this is a function of the total station, but none of the signal is returned or retro reflected from the monitoring prism to the receiver optics resulting in measurement failure.

To test and certify a montioring prism / survey prism at a stated accuracy you must test all six aspects of the glass reflection and qualify the largest rate of divergence as the monitoring prism beam divergence. If a monitoring prism is stated at 1.5” seconds then all six aspects have performed at or better than 1.5” of divergence.

Reflector Accuracies - Prism Monitoring

Figure 3

Figure 3 shows the results from an Interferometer measurement taken to determine the homogeneity of all aspects of a monitoring prism.

REFLECTIVE COATINGS

The ability of a monitoring prism / survey prism to return an emitted signal is greatly affected by the reflective qualities of medium or material.

While glass ground at angle provides a reflection, monitoring prisms benefit from a reflective coating such as gold silver or copper by as much as 30%. The application of this reflective coating enhances the ability of the monitoring prism to return a signal with sufficient intensity, hence increasing the operating range of the monitoring prism.

Prism Monitoring

Figure 4

Figure 4 shows the reflective qualities of gold, silver, copper and aluminium coatings at varying wavelengths. Leica instruments used in the field testing of monitoring prisms operate between 0.66µm and 0.85µm frequencies. If you plot this wavelength on the chart you will see there is a minimal difference between the performance of gold, silver and copper, all operating at approximately 95%.

 

For ease of identification Pangea Geosystems decided to utilise the copper coating which is clearly visible to the naked eye on the translucent glass. It is more difficult to confirm the presence of a silver coating.

ENVIRONMENTAL FACTORS

When manufactured, test monitoring prisms / survey prisms in real world conditions, they are typically in optimal conditions devoid of environmental factors. As such, the stated range of a mmonitoring prism / survey prism comes with a qualification statement that this range is achievable in optimal conditions. These types of conditions are rarely experienced on a mine site. The addition of extreme heat/cold, wind, dust and rain affect the beam divergence and intensity of the signal greatly reducing the operating range of the monitoring prism. In these scenarios, the reflective qualities of the monitoring prisms are exacerbated.

 

Due to the environment experienced on a mine site it is crucial to select a monitoring prism that will give you the strongest reflective intensity at range. The selection of the correct monitoring prism will ensure that the monitoring prism works at a range that exceeds the distance required over the projected life of the prism. This can be achieved by selecting a monitoring prism / survey prism with a good reflective coating and small beam deviation, 2 arc seconds or better.

Prism Monitoring

Figure 5

Figure 5 depicts the reduction in range over time due to the degradation in signal strength and reflective qualities from a monitoring prism > than 2 arc seconds. If such a monitoring prism is placed at the limit of the operating range early in the lifecycle the observations to the monitoring prism may start to fail briefly after installation, often as a result of dust settling on the prism lens. Additional to this, repeatability may be compromised if there are environmental events such as those experienced on mine sites, where prism measurements may fail intermittently due to a reduction in range.

Prism Monitoring

Figure 6

Alternately, figure 6 shows where a monitoring prism with < 2 arc seconds of beam deviation has been installed at the same distance with considerations of range over the lifecycle of the monitoring prism. Even when affected by environmental events or signal/prism degradation over time the monitoring prism continues to provide repeatability throughout its lifespan.

 

For these reasons, substandard monitoring prisms / survey prisms may appear to work while newly installed but begin to fail or have repeatability issues much earlier in the lifecycle in comparison to a considered option.

FIELD MONITORING PRISM TESTING RESULTS

Pangea Geosystems collected monitoring prisms / survey prisms from many manufactures with differing qualities. Coating types or a lack there of, accuracy/beam divergence, housing types, backing paint and glass construction were all considerations based around the research undertaken. Once many monitoring prisms / survey prisms were collected, field testing was conducted to assess the range and performance of similar monitoring prisms / survey prisms under the same climatic conditions.

 

Baselines were established over 1500m, 1900m, 2250m, 2500, 2750m and 3000m and the repeatability of the ATR function and EDM measurement were tested. To achieve a successful reading at range, or pass mark, the monitoring prism / survey prism was required to return greater than 66% of the time.

 

Results are as follows in Figure 7 (below).

Field Prism Testing Results - Prism Monitoring

Figure 7

While testing monitoring prisms in the field it was also noted that monitoring prisms specified to the same specification and accuracy, supplied by the same manufacturer performed differently. Further investigation on the QAQC process of these manufacturers revealed that the accuracy was only tested periodically from the production line, rather than each monitoring prism being tested and certified using an Interferometer.

ALIGNMENT

Another aspect field tested but not collated in the charted results above was the angle of incidence. All the results above in the chart are when the monitoring prism has been aligned perpendicular to the total station. At any distance greater than 1500m, if the angle of incidence was greater than 20 the prism stopped returning the signal.

Alignment - Prism Monitoring

Figure 8

In addition to the angle of incidence required for repeatable measurements, the distance measurement will also be adversely affected when the prism is misaligned with the incoming signal. The rate of distance deviation in relative to the angle of incidence as displayed below in Figure 9.

Distance Deviation - Prism Monitoring

Figure 9

MONITORING PRISM RESEARCH - CONCLUSION

Field monitoring prism testing conducted by Pangea Geosystems revealed the design considerations required for accurate, repeatable measurements with monitoring prisms . survey prisms. The ideal monitoring prism for use in deformation monitoring in the mining environment will possess the following characteristics:

 

  • 64mm ɸ round glass construction,

  • coated with either gold, silver or copper (copper being easily identifiable),

  • treated with backing paint,

  • sealed and weather resistant,

  • have an accuracy of 2 arc seconds or better,

  • be individually tested and certified, and

  • should be installed with a mounting bracket to achieve optimal alignment.

 

Where monitoring prisms possess the above listed characteristics, the highest level of results will be achieved for the longest time, hence underpinning the investment in deformation monitoring systems.

bottom of page